Price Factors Affecting China Swing Beam Shear Machine

The price of a China Swing beam shear machine is always people's focus, when consumers buy products, they yell out, "how much is this equipment" and generally, they will consider whether to continue to understand the equipment according to the quotation, we all know that the price of a thing is not set arbitrarily. Manufacturers have to decide according to various factors,What are the specific factors that affect the price of the China Swing beam shear machine?

Different Tonnage, Different Price

The cargo of the shearing machine is different,The larger the cargo is, the higher the work efficiency and the higher the price,On the contrary, the smaller the cargo, the lower the price.

Different Models, Different Prices

china Swing beam shear machine


The same is true for a type of product,To meet the requirements of different customers, manufacturers will manufacture various types of products. Some special types of products will be more expensive, and ordinary products will generally be about the same price.

Different Manufacturers, Different Prices

Some Swing beam shear machine manufacturers are relatively large, and the products they produce are of excellent quality and good reputation,The price is generally slightly higher. Both the production and labor costs will be lower, so the equipment price will also be lower.

The Impact Of Supply And Demand

If there is an oversupply of a product for some time, the price will be lower; when there is a shortage of a product, the price will be higher.

Buy Must Look At The Quality

Generally, various factors affect the price of the Swing beam shear machine,In purchasing a product, you can't just choose the price,In addition to the price, the quality is more important. Therefore, when purchasing a product, know that the price is not outrageously high compared with its peers.If the quality is better, it is okay to spend a little more money because good quality products can reduce maintenance costs later.

Precautions Of The China Swing Beam Shear Machine

A swing beam shear machine is a piece of shearing equipment widely used in machining, It can cut steel plate materials of various thicknesses. Commonly used shearing machines are divided into flat shear, rolling shear, and vibration shear,The shearing machine is used for a large amount.

The shearing machine with a shear thickness of less than 10mm is mostly mechanical transmission, and the shearing machine with a shear thickness of more than 10mm is a hydraulic transmission. Generally, it is operated by foot or button for single or continuous metal shearing.

A swing beam shear machine is a circular arc movement, and the production of circular arc blades is quite difficult. Generally, the blade is used to make up horns, so the obtained gap is not accurate, and the cut sheet is not very ideal because it is an Arc-shaped movement; the blade can not be made into a rectangle but should be made into an acute angle, so the force of the blade is not ideal. The damage to the blade is also severe.

What Should Be Paid Attention To When Operating

Do It Carefully Before Work

  • Before the dry running test, the machine should be manually cranked for a working stroke, and the equipment can be started only after confirming that it is normal.
  • For equipment with hydraulic devices, check that the oil storage tank's oil volume should be sufficient. After starting the oil pump, check whether there is leakage in the valve and pipeline. The pressure should meet the requirements. Open the air valve to release the air into the system.

Do It Seriously At Work

 Swing beam shear machine


  • In many China Swing beam shear machine manufacturers, it is considered that it is not allowed to cut laminated sheets, trim the edges of burr sheets, and cut thin sheets and short sheets that are not tightly compressed.
  • The gap between the blades should be adjusted according to the thickness of the sheet but should not be greater than 1/30 of the thickness of the sheet,The blade should be fastened firmly, and the upper and lower blade surfaces should be kept parallel, After adjustment, manual turning inspection should be used to avoid accidents.
  • The cutting edge of the blade should be kept sharp,If the cutting edge becomes dull or cracked, it should be replaced in time.
  • When cutting, the pressing device should firmly press the sheet, and it is not allowed to cut in a state where it is not pressed tightly.
  • For equipment with hydraulic devices, other hydraulic valves except the throttle valve are not allowed to be adjusted without permission,The thickness of the sheet material sheared by the pendulum shearing machine should be determined according to the instructions given by the manufacturer.

 Do It Carefully After Work

After work, the upper blade should be placed in the lowest position.

Safe Maintenance

For safe operation, machine tools using mechanical, hydraulic, electrical, and electronic devices are all high-risk machine tools, Except for those listed in this manual, professional maintenance personnel must carry out other maintenance.

  • A special person must handle the Swing beam shear machine, and the operator must read the manual and the CNC system operation manual before operating the machine.
  • When multiple people operate the machine, one person must be designated to operate the machine,Only when it is confirmed that there is no unsafe factor can one step on the footswitch or press the button to avoid accidents.
  • When placing the sheet on the workbench and positioning it with the back gauge, the fingers should not be placed between the sheet and the workbench. Do not push the sheet to position before the back gauge reaches the positioning point to avoid injury.
  • When the machine is working, no tools or sundries should be placed between the work surface and the knife-edge, and there should be no defects such as welding scars on the surface of the workpiece to avoid damage to the blade.
  • It is necessary to strictly follow the thickness, material, and width of the shearable plate and let the numerical control system automatically calculate it before cutting. It must not be overloaded to avoid damage to the machine,Our company is not responsible for damage caused by overloading the machine.
  • Electrical insulation and grounding must be safe and reliable.
  • The above is the operation and price factors of the China Swing beam shear machine brought to you,I hope you will help me when purchasing it after reading it. If you have any questions, please feel free to contact us, and we will reply to you as soon as possible.
Share on facebook
Share on twitter
Share on linkedin

More bending machine information

request a quote