200Ton/3200mm CNC Hydraulic Press Brake Sheet Metal Bending Machine WE67K Series

Brief introduction

CNC Hydraulic Brake Sheet Metal Bending Machine is a product developed by XIYUAN MACHINE that focuses on high-precision sheet metal bending. Combining Xiyuan Machine's leading bending technology and comprehensive expertise, it focuses on improving bending efficiency and bending accuracy. Reduce waste and have a high cost performance ratio. Compact and practical, and with higher stability, it is the best choice for you to do mass processing and increase productivity.

Operation method

• The first is to turn on the CNC Hydraulic Press Brake Sheet Metal Bending Machine, turn on the key switch on the control panel, and then press the oil pump to start, so you can hear the rotating sound of the oil pump. (The machine does not work at this time)
• Stroke adjustment, when using CNC Hydraulic Press Brake Sheet Metal Bending Machine, you must pay attention to adjusting the stroke, and be sure to test the car before bending. When the upper die of the bending machine goes down to the bottom, there must be a gap of sheet thickness. Failure to do so will cause damage to the mold and machine. The stroke adjustment also includes electric quick adjustment and manual stomach adjustment.
• Bending notch selection, generally choose a notch with a width of 8 times the thickness of the plate. For bending 4mm plates, select 32 or so notches.
• The rear gear adjustment generally has electric quick adjustment and manual fine-tuning, and the method is the same as the shearing machine.
• Press the foot switch to start bending. The CNC Hydraulic Press Brake Sheet Metal Bending Machine is different from the shearing machine. It can be released at any time. When you release the foot, the bending machine stops, and continues to go down while stepping on it.

Maintenance content

• The oil change work shall be carried out for the first time after one month of operation of the equipment, and once a year thereafter. Also, when changing oil, the fuel tank must be cleaned at the same time.
• The hydraulic oil grade it uses shall be determined according to the actual situation.
• Pay attention to the system oil temperature at any time. Normally, it should be within the range of 35℃-60℃, and the maximum should not exceed 70℃.
• At the same time as the oil is replaced, the filter should be thoroughly cleaned.
• After the equipment is used for one month, the tubing should be checked for deformation at the bend. After two months of use, you should check if the fastener is tight.

WE67K 200 Ton 3200mm 4+1 Axis CNC Hydraulic Press Brake Sheet

The bending moment stiffness and tensile strength are high, the ST44 A1 material is used, and it is equipped with a user-friendly user interface that provides all the main press brake functions.

High Positioning BACKGAUGE

• Standard X-axis travel is 500mm, with a third measurement step, capable of measuring parts up to 600mm using standard backgauge (most machines)
• Stable AC servo motor drives precision X-axis back gauge, WE67K 200 Ton 3200mm 4+1 Axis CNC Hydraulic Press Brake Sheet with linear guide and ball bearing system.
• Back gauge finger with two measuring steps, one for short bending depths and the other for long bending depths.
• Backward positioning refers to ±0.01 mm movement along the linear bearing. Positioning tolerance.

Specification

• Model: WE67K 200 Ton 3200mm 4+1 Axis CNC Hydraulic Press Brake Sheet
• technical details:
• Main motor: 15Kw
• Controller system: 1. Dutch brand: Delam DA65W 4+1 axis: Y1, Y2, X, R+ table crowning system
• Fuel tank volume: 560L
• Weight: 10300 kg
• Dimensions: L 3450 mm，Width 2145 mm，Height 2960 mm
• Ordinary press: 200 tons
• Table length: 3200mm
• Shell spacing: 2650mm
• Throat depth: 320mm
• Plunger stroke: 200mm
• Punch speed: 80/8/80 mm/s
• Open height: 480mm