3分钟了解摆式剪板机

Steel can become a helpful talent because it has undergone various trials and fiery tests in the smelting process. To become a valuable “talent”, people also need to meet challenges in innovation and experience the difficulty of life. A swing beam shearing machine is widely used with simple operation and quick start, which can shear stainless steel, ordinary carbon steel, copper iron and other plates.

选购摆式剪板机注意事项翼梁剪板机

摆梁式剪板机、数控折弯机、电动剪板机等机床购置后成为固定资产。因此,选购时应特别注意产品质量。好的设备使用寿命长,但工作效率高,作为固定资产投资,损失小。

首先考虑钣金板材以及需要由摆式剪板机共用的金属板材的最大加工厚度和长度。使用这些来确定所购买设备的型号。当然,你不确定的时候也可以联系马鞍山西苑厂家推荐。

在购买摆式剪板机时尤其要注意扩大企业的规模,在确定设备的型号之前最好留有一定的余量。选好机器型号后,详细了解周边购买的摆式剪板机的使用情况,机器的质量,尤其是售后服务。

确认哪些制造商生产购买摆式剪板机。在这个环节,朋友们往往会被忽略,因为无论联系哪个厂家,厂家都会告知专业生产这个产品。

事实上,不同厂家生产的型号往往是不同的,厂家往往通过调货来提供各种型号的产品。此类外购产品的售后服务可靠性较差。推荐马鞍山西源机械科技有限公司。

Our company integrates production and sales and independently develops and produces various QC11K CNC Guillotine Shearing Machine With E21S, QC12k Swing Beam Cutting Machine With E21s Sheet, QC12K 16×3200 Hydraulic Swing Beam Cutting Machine With E21S, etc. Equipment, installation, use and maintenance in after-sales service will guide you one by one, and the quality is guaranteed.

After you can contact China Swing beam shearing machine suppliers to obtain the machine’s price, parameters, payment, and delivery method, the most crucial step is choosing the manufacturer to buy. Generally, a trusted manufacturer is selected after removing the highest and lowest prices to obtain better cost performance and, at the same time, ensure quality and after-sales service.

摆式剪板机启动前

  • The machine operator must be familiar with the Swing beam shearing machine’s main structure, performance, and usage.
  • 检查开关是否完好,控制柜和控制台按钮是否完好,各部件是否松动。
  • 检查工具安装是否正确,有无松动、倾斜或杂物。
  • 检查各动作机构是否松动、损坏或异常。
  • 检查摆式剪板机周围和内部是否有妨碍发动机运转的物体。
  • 给摆式剪板机的润滑点上油。
  • 摆式剪板机启动中国翼型剪板机
  • 启动油泵,接通电源。
  • 按下电机启动按钮。
  • 等待几分钟,直到摆式剪板机电机完全进入运行状态。
  • 将手动开关打到单一位置,手动试动摆梁剪板机的剪板,确认正常。
  • 根据被切材料的厚度调整刀片间隙。
  • Adjust the master or fixture according to the shared material’s width.
  • 先做1~3个空行程,待正常后即可进行剪切工作。
  • 将要切割的产品按工艺要求放好。
  • 踩下脚踏开关切割产品。

防范措施

  • 本机床适用于共用各种材料厚度为机床额定值的钢板、铜板、铝板及非金属材料板材。
  • 必须是无硬痕、焊渣、夹渣和焊缝的材料,厚度不允许过大。
  • 取放产品时,应在上升稳定后进行。小心刀子滑下来伤到你的手。
  • 不得切割层压板、修整原板边缘、切割未压紧的薄、短板。
  • 刀片的刃口应保持锋利。如果刃口变钝或开裂,应及时更换。
  • 裁切时,压紧装置要用力压紧板材,不允许在未压紧的状态下裁切。
  • 维修前必须完全关闭设备电源。
  • 及时清理摆式剪板机周围的油污,防止打滑。
  • 禁止用敲击的方式拧紧塞子或调整刀片间隙。改变导轨间隙和刀片间隙时,应先停车,再进行。工作过程中严禁用手进入切割区或用手拾取材料。

摆式剪板机完成后

  • 按下电机停止按钮。
  • 关闭油泵。
  • 检查每个操作开关是否不工作。
  • 清理摆式剪板机内外、杂物、杂物,保证清洁。
  • 整理打扫工作环境,确认清洁度。

保养注意事项

  • Clean the inside and outside of the pendulum shearing machine every day: Before starting the swing beam shearing machine engine, the inside and outside of the equipment must be cleaned to ensure that there are no debris and oil stains. This is because debris or oil can damage the machine’s parts and reduce its efficiency. Regular cleaning of the machine will help prevent these problems and keep the machine in good condition.
  • 每天检查是否漏油:检查是否漏油对于保持机器正常运行至关重要。漏油会造成机器部件的损坏,还会造成安全隐患。因此,有必要检查机器各部分,如液压系统、切割刀片是否漏油,并立即解决。
  • 每天润滑您的设备:润滑对于保持机器性能和减少磨损至关重要。启动机器之前,请确保机器润滑良好。这有助于防止机器部件之间的摩擦并降低损坏风险。
  • 检查零件是否松动、损坏或移位:随着时间的推移,机器的零件可能会因正常使用而松动、损坏或移位。这会导致效率降低,甚至造成安全隐患。因此,必须经常检查设备各部位的所有螺栓及零件,并及时紧固或修理。这包括检查切割刀片、液压系统、电机和机器的其他关键部件。定期检查有助于及早发现问题并防止问题变得更加严重。
  • Follow the manufacturer’s maintenance schedule: The manufacturer’s maintenance schedule must be followed to ensure that the machine is properly maintained. The manufacturer’s schedule will include recommended maintenance tasks such as oil changes, filter changes, and other necessary maintenance activities. By following the manufacturer’s maintenance schedule, machines can run at their best and stay in good shape for a long time.

In summary, maintaining a swing beam shearing machine requires regular cleaning, checking for oil leaks, lubrication and inspection of the machine’s parts. By following these precautions and the manufacturer’s maintenance schedule, machines can operate reliably, efficiently and safely, helping to increase productivity and reduce downtime.

相信vid可以创造更好的设备

To grasp innovation is to learn development, and to hold innovation is to get the “bullnose” of development. “I’m not afraid of not doing it well, but I’m so scared not to do it. The innovative technical transformation has been done well. The above is the relevant knowledge of the 摆梁剪板机 introduced. If you have any questions you don’t understand, please get in touch with us, and we will promptly give you a reply.

分享到 facebook
Facebook
分享到 twitter
推特
分享到 linkedin
领英

更多折弯机信息

请求报价